IAP2300C Series
DIN-Rail or Wall Mounting
Industrial Wireless Client
Support 5 100M copper ports, 1 RS-232/485 serial port
Support 2.4GHz and 5GHz dual bands, and can accommodate up to 4*2.4G/5G dual-band antennas.
Support multiple wireless network modes such as client, route, AP, bridge and dual-link mode
Support multiple serial port modes like RealCom, TCP Server, TCP Client, UDP Server, UDP Client
Support conversion between Modbus RTU/ASCII and Modbus TCP protocol
Support 12~36VDC power supply input
Support -40~75℃ wide operating temperature range
Introduction
IAP2300C series are 100M industrial wireless clients. This series have 2 products, providing 100M WAN port, 100M LAN port, 2.4G/5G dual-band antenna interface, serial port and other interfaces. This series of products provides one serial port, and supports serial port server or Modbus gateway, so that serial port devices can be equipped with networking capability immediately or realize the conversion between Modbus RTU/ASCII and Modbus TCP protocol. This series product supports DIN-Rail or wall mounting, which can meet the requirements of different scenes.
The network management system supports client, route, AP, bridge and dual-link wireless work modes; Support IEEE802.11a/b/g/n wireless technology, and the maximum overall wireless rate of the dual-band device can reach 600 Mbps; The device supports wireless encryption methods such as WPA/WPA2/WPA3 (personal and enterprise editions), and has various security policies such as SSID hiding, wireless user isolation, IP filtering, MAC filtering, URL filtering, DNAT settings, SNAT settings, ARP binding, DMZ settings, etc. Support virtual AP, that is, one device supports multiple SSIDs. The device supports single-band wireless fast roaming, client efficient roaming, dual-link seamless roaming. And the efficient roaming takes only about 50 milliseconds, which can meet the requirements of rapid roaming and recovery of wireless data in industrial occasions. Dual-link seamless roaming, that is, in the WLAN (Wireless Local Area Network) constituted by multiple AP, user can achieve seamless roaming without conducting the AP switching operation. In serial server mode, each serial port supports 4 TCP or UDP session connections and multiple work modes like RealCom, TCP Server, TCP Client, UDP Server, UDP Client. Under Modbus protocol mode, work modes such as RTU Master, RTU Slave, ASCII Master and ASCII Slave are supported. Up to 256 Modbus TCP Client (Master) devices can be accessed, and 128 Modbus TCP Server (Slave) devices can be connected.
RESET button can restore the device to factory defaults or perform a reboot. Hardware adopts fanless, low power consumption, wide temperature and voltage design and has passed rigorous industrial standard tests, which suits the industrial scene environment with harsh requirements for EMC. It can be widely applied in industrial fields such as AGV vehicles, inspection robots, video surveillance, data acquisition, warehousing, and logistics.
Technical Specifications
Standard & Protocol | IEEE 802.3 for 10Base-T IEEE802.3u for 100Base-TX IEEE802.11a/b/g/n for WLAN IEEE802.11i for wireless security IEEE802.11r for fast roaming IEEE802.11e for WMM |
Work Mode | Route mode AP mode Bridge mode (connection: WDS bridge, universal bridge; fast roaming) Client mode (connection: WDS bridge, universal bridge, wireless NAT; fast roaming/efficient roaming) Dual-link mode (connection: Dual-WDS bridge, Dual-universal bridge, Dual-wireless NAT; Seamless roaming) Note: Only 2E2E dual-band devices support dual-link mode. |
WLAN | WPA/WPA2/WPA3 personal/enterprise edition encryption mode, hidden wireless SSID, wireless user isolation, wireless transmission power adjustment, maximum user limit, packet segmentation and RTS threshold, China/US wireless channel, WDS, WMM |
Management | Intranet settings, extranet settings (routing mode/wireless NAT), wireless settings-client, wireless settings-AP, AC management, SNMP management, roaming agent, seamless roaming, QoS management, wireless probe, user settings, system upgrade, timed restart, profile management, system log, log management, wireless user list, Wi-Fi real-time traffic monitoring, serial port application, serial port log, Modbus settings |
Security Policy | Wireless users: black/white list of wireless users and event notification of wireless users. Firewall: IP filtering, MAC filtering, URL filtering, DNAT setting, SNAT setting, ARP binding, DMZ setting |
Routing/Switching | Static routing (routing mode/wireless NAT) |
Troubleshooting | Network detection, Ping, route tracing |
Time Management | NTP Client |
Radio Frequency | 802.11b/g/n: 2.412GHz~2.4835GHz 802.11a/n: 5.18GHz~5.825GHz RF power output: 20dBm Modulation methods: DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM |
Receiving Sensitivity | 802.11b: -95dBm@1Mbps, -89dBm@11Mbps 802.11g: -90dBm@6Mbps, -74dBm@54Mbps 802.11a: -89dBm@6Mbps, -72dBm@54Mbps 802.11n: -85dBm@MCS0, -67dBm@MCS7 |
Transmitting Power | 802.11b: 23dBm@1Mbps, 20dBm@11Mbps 802.11g/a: 23dBm@6Mbps, 20dBm@54Mbps 802.11n: 23dBm@MCS0, 20dBm@MCS7 |
Interface | Antenna interface: 2.4G/5G dual-band antenna interfaces, RP-SMA-K (Female) 100M WAN: 10/100Base-T(X) RJ45 port 100M LAN: 10/100Base-T(X) RJ45 port Serial port: RS-232/485 serial port adopts 2*5PIN 3.81mm pitch terminal blocks (serial port occupies 6 pins) |
Serial Port Parameter | Standard: EIA RS-232C, RS-485, RS-422 RS-232 signal: RXD, TXD, GND RS-485 signal: D+, D-, GND Baud rate: 300~115200bps Data bit: 8bits Parity bit: None, Even, Odd Stop bit: 1bit, 2bit Directional control: RS-485 direction adopts Automatic Data Direction Control technology Load capacity: RS-485 terminal supports 32-node polling environment Pull up/down resistance for RS-485: 4.7kΩ Work mode: Serial server: RealCom Mode, TCP Server Mode, TCP Client Mode, UDP Server Mode, UDP Client Mode, each serial port supports 4 TCP/UDP sessions Modbus gateway: RTU Master, RTU Slave, ASCII Master, ASCII Slave, support up to 256 Modbus TCP Client (Master) device accesses and 128 Modbus TCP Server (Slave) device connections |
Indicator | Running indicator, WLAN indicator, RSSI indicator, WAN indicator, LAN indicator, serial port indicator |
Power Supply | Input voltage: 12~36VDC, support anti-reverse connection Connection method: 2*5PIN 3.81mm pitch terminal blocks (includes 4-pin power supply) |
Power Consumption | IAP2300C-2E-5T-1D-P12_36 No-load at normal temperature: 1.79W@12VDC Full-load at normal temperature: 2.82W@12VDC Full-load at high temperature: 4.20W@12VDC IAP2300C-2E2E-5T-1D-P12_36 No-load at normal temperature: 3.36W@12VDC Full-load at normal temperature: 8.54W@12VDC Full-load at high temperature: 9.15W@12VDC |
Working Environment | Operating temperature: -40~75℃ Storage temperature: -40~85℃ Relative humidity: 5%~95% (no condensation) |
Mechanical Structure | Housing: IP40 protection, metal Installation: DIN-Rail or wall mounting Dimension (W x H x D): 30mm×124mm×96mm Weight: IAP2300C-2E-5T-1D-P12_36: 0.425kg IAP2300C-2E2E-5T-1D-P12_36: 0.508kg |
Industrial Standard | IEC 61000-4-2 (ESD, electrostatic discharge), Level 3 Air discharge: ±8kV Contact discharge: ±6kV IEC 61000-4-4 (EFT, electrical fast transient pulses), Level 3 Power supply: ±2kV Signal: ±1kV IEC 61000-4-5 (Surge), Level 3 Power supply: common mode ±2kV, differential mode ±1kV Signal: common mode±2kV, differential mode±1kV Shock: IEC 60068-2-27 Free fall: IEC 60068-2-31 Vibration: IEC 60068-2-6 |
Authentication | CE, FCC, RoHS |
Warranty | 5 years |
Optional Accessories
Type | P/N | Gain (dBi) | Interface | Length (m) | Quantity (pcs) | Remark | ||
2E | 2E2E | |||||||
Omnidirectional glue stick antenna | 3005040132 | 2 | RP-SMA-J | — | 2 | 4 | Standard for 2E; Optional for 2E2E | |
Omnidirectional glue stick antenna | 3005040216 | 5 | RP-SMA-J | — | 2 | 4 | Optional | |
Sucker feeder | 3005040092 | — | RP-SMA-J to RP-SMA-K | 1.2m | 2 | 4 | Optional | |
Sucker feeder | 3005040096 | — | RP-SMA-J to RP-SMA-K | 3m | 2 | 4 | Optional | |
Feeder | 3005040182 | — | RP-SMA-J to RP-SMA-K | 1.5m | 2 | 4 | Optional | |
Feeder | 3005040183 | — | RP-SMA-J to RP-SMA-K | 3m | 2 | 4 | Optional | |
Ordering Information
Documentation & Downloads
Make an appointment with an expert to receive a free assessment of your industrial network needs










