IMF2100 Series
DIN-Rail Mounting
1/2 Optional Fiber Ports + 1 RS-232/485/422 Serial Port Optical MODEM
Support 1/2 optical fiber interfaces and 1 RS-232/485/422 with isolated serial port
Support one relay alarm output for power failure alarm and optical fiber disconnection alarm
Support ring network topology with one master and multiple slaves; serial-to-fiber conversion delay below 15μs
Support 300bps~115200bps serial port baud rate
Support 12~48VDC dual power supply, 110~370VDC or 85~265VAC and other power supply schemes
Support -40~75℃ wide operating temperature range
Introduction
IMF2100 series are 1/2 optional fiber ports + 1 RS-232/485/422 serial port optical MODEMs, which convert RS-232/485/422 serial signal into optical signal, provide RS-232/485/422 serial port to users, and realize end-to-end transparent transmission. This series of products provide one or two optical fiber interfaces and one RS-232/485/422 serial port; The power supply supports 12~48VDC dual power supply, 110~370VDC or 85~265VAC (optional); 2 optical fiber interface products support ring network function. This series of products adopt DIN-Rail installation mode, which can meet the needs of different application sites.
The design of the DIP switch can realize the functions including master/slave ring network selection, RS-485 terminal resistance enable, relay power failure alarm and relay optical fiber disconnection alarm (Note: the power alarm function is only for dual power supply products). When the optical fiber disconnects or the dual power supply has failure, the ALM indicator will be bright and send out alarm, meanwhile, the alarm device connected to the relay will send out alarm for rapid scene troubleshooting. Hardware adopts fanless, low power consumption, wide temperature and voltage design and has passed rigorous industrial standard tests, which can fit the industrial scene environment with harsh requirements for EMC. It can be widely used in various industrial control, process control, traffic control, intelligent community, and other occasions, especially suitable for banks, electric power and departments and systems with special requirements for electromagnetic interference environment.
Technical Specifications
Fiber Interface | Interface quantity: 1/2 (support ring network) Interface form: optional SC/FC/ST interfaces Transmission distance: multimode: 2km single mode: 20/40/60km Transmission wavelength: multimode: 1310nm single mode: 1310nm or 1550nm |
Serial Port | Standard: EIA RS-232C, RS-485, RS-422 standard Serial port quantity: 1 RS-232/485/422 serial port. Serial ports of different modes cannot be used simultaneously RS-232 signal: RXD, TXD, GND RS-485 signal: D+, D-, GND RS-422 signal: T+, T-, GND, R+, R- Baud rate: 300~115200bps Data bit: 5bit, 6bit, 7bit, 8bit Stop bit: 1bit, 1.5bit, 2bit Parity bit: None, Even, Odd, Space, Mark Interface form: 7-pin 3.81mm pitch terminal blocks Directional control: RS-485 direction adopts Automatic Data Direction Control technology Load capacity: RS-485 supports 32-point polling (customizable 128 points) Pull up/down resistance for RS-485: 4.7kΩ RS-485 terminating resistor: 120Ω, can be enabled or disabled via a dip switch. Transmission distance: RS-232, 15m, RS-485/422 serial port, 1200m |
Relay | Relay quantity: 1 relay alarm output Connection method: 6-pin 5.08mm pitch terminal blocks (includes 2-pin relay) Current load: 1A@30VDC, 0.3A@125VAC Default relay state: normally open |
Indicator | Operation indicator, power indicator, alarm indicator, master/slave indicator, fiber port connection and data indicator, serial port receiving data indicator, serial port sending data indicator |
Power Supply | Supports 3 power supply options: 12~48VDC dual power supply, 110~370VDC, or 85~265VAC Scheme 1 Power supply range: 12~48VDC dual power supply Connection method: 6-pin 5.08mm pitch terminal blocks (includes 4-pin power supply) Power supply protection: non-polarity, built-in 2.0A overcurrent protection Power supply redundancy: support Scheme 2 Voltage range: 110~370VDC Connection method: 6-pin 5.08mm pitch terminal blocks (includes 2-pin power supply) Power supply protection: non-polarity, built-in 2.0A overcurrent protection Scheme 3 The power supply range is 85~265VAC Connection method: 6-pin 5.08mm pitch terminal blocks (includes 2-pin power supply) Power supply protection: built-in 2.0A overcurrent protection |
Power Consumption | No-load at normal temperature: 2.55W@12VDC Full-load at normal temperature: 2.62W@12VDC Full-load at high temperature: 2.83W@12VDC |
Working Environment | Operating temperature: -40~75℃ Storage temperature: -40~85℃ Relative humidity: 5%~95% (no condensation) |
Mechanical Structure | Housing: IP40 protection, metal Installation: DIN-Rail mounting Weight: 0.327kg Dimension (W x H x D): 35mm×110mm×95mm |
Industrial Standard | IEC 60950-1 / EN 60950-1: Safety EN 55032: Conducted & Radiated Disturbances IEC 61000-3-2 Harmonic Current Emission IEC 61000-3-3 Voltage Fluctuation & Flicker EN 55024 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 IEC 61000-4-11 |
Authentication | CE, FCC, RoHS |
Ordering Information
IMF2100-1F-1DI(3IN1)-TB-2P(12-48VDC)
Fiber Port
1
RS-232/485/422
1
Power Supply
12~48VDC dual power supply
IMF2100-2F-1DI(3IN1)-TB-2P(12-48VDC)
Fiber Port
2
RS-232/485/422
1
Power Supply
12~48VDC dual power supply
IMF2100-1F-1DI(3IN1)-TB-P(110-370VDC)
Fiber Port
1
RS-232/485/422
1
Power Supply
110~370VDC
IMF2100-2F-1DI(3IN1)-TB-P(110-370VDC)
Fiber Port
2
RS-232/485/422
1
Power Supply
110~370VDC
IMF2100-1F-1DI(3IN1)-TB-P(85-265VAC)
Fiber Port
1
RS-232/485/422
1
Power Supply
85~265VAC
IMF2100-2F-1DI(3IN1)-TB-P(85-265VAC)
Fiber Port
2
RS-232/485/422
1
Power Supply
85~265VAC
Documentation & Downloads
Recommended Products
MODEL277 Series
Wall Mounting or DIN-Rail Mounting
1 RS-232/485/422 Serial-to-Fiber Modem
MC201-F Series
Wall Mounting
1 CAN to Fiber MODEM
IMF208-2F
Wall Mounting
8 RS-485 + 2 Fiber Ports Unmanaged Ring Network Serial to Fiber MODEM
IMF204-2F Series
Wall Mounting
4 RS-485 and 2 Fiber Port Unmanaged Ring Network Serial to Fiber MODEM
Make an appointment with an expert to receive a free assessment of your industrial network needs










